• BMR 16-17 6th Gen Camaro Rear Hollow 32mm Non-Adj. Sway Bar Kit - Red
1 1

BMR Suspension

BMR 16-17 6th Gen Camaro Rear Hollow 32mm Non-Adj. Sway Bar Kit - Red

BMR 16-17 6th Gen Camaro Rear Hollow 32mm Non-Adj. Sway Bar Kit - Red

$ 299.95
$ 329.95 $ 299.95
Free shipping on orders over $99 (contiguous U.S.) โ€” flat $10.99 under $99. Shipping details
โœ• Out of Stock
Ships from BMR Suspension โ€” this item ships direct from the manufacturer. It usually goes out quickly, but because it leaves their warehouse rather than ours, delivery can take a little longer than our in-stock parts.

These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing.BMR's suspension designed the SB051 sway bar kit for street performance, autocross, and road race applications. The large sway bars single position give you the ability to drive to and from the road course or autocross and still out handle the competition with the same sway bars. The SB051 rear bar gives you a 52 increase in rate over the stock bar. This rate increase allows you to drive harder through corners with minimal body roll. The hollow design allows for loads of strength in the lightest package possible. This means increased performance with no sacrifices. The SB051 attaches to your Camaro with 88-durometer polyurethane bushings, reducing the deflection from the stock rubber bushings. This allows for more sway bar control, which equals better handling. When performance is a must, rely on BMR's suspension!BMR's suspensions SB051 sway bar kit is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.!Does Not Fit Convertible Cars BMR Suspension designed the SB051 sway bar kit for street performance, autocross, and road race applications.

  • Manufactured from 1.25-inch heavy-wall DOM tubing for increased strength
  • Designed for street performance, autocross, and road race applications
  • Fits 2016-Newer Chevrolet Camaro(excluding cars with ELSD)
  • 52% increase in sway bar rate over stock sway bar
  • Cold formed to better resist torsional fatigue
  • 88-durometer, greasable polyurethane bushings
  • Dramatically reduces body roll
  • Proudly designed in the U.S.A.
  • 1-2 hour installation time
  • Proudly made in the U.S.A.
  • Zinc-plated inner sleeves
  • Durable powdercoat finish

Vehicle Fitment

  • 2016-2024 Chevrolet Camaro

Please verify exact fitment for your trim and engine before ordering.

Manufacturer Part Number: SB051R

Images are for illustrative purposes only. Actual product may vary.

โš  WARNING (California Proposition 65): This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.

Manufacturer's Warranty โ€” BMR Suspension

BMR Suspension warrants its products to the original purchaser against defects in materials and workmanship under normal use for two (2) years from the date of sale. BMR's obligation under this warranty is limited to replacement of the product — reinstallation and other incidental costs are not covered — and warranty claims are limited to replacement or credit for returned merchandise. The warranty does not apply to products that have been misused, neglected, altered, damaged or improperly installed, and normal wear is not considered a defect. Impact damage and damage to powder coat are specifically excluded. An RMA is required for all warranty returns; replacement product ships at no charge via UPS Ground, and upgraded shipping is available at the customer's expense for the difference in cost. BMR products are designed for use with OEM and other BMR products — BMR does not warrant fitment with aftermarket products from other manufacturers, including suspension, exhaust, drivetrain or other aftermarket components; returns due to fitment issues with OEM or BMR products receive a full refund, while returns due to fitment issues with another manufacturer's aftermarket parts are subject to a 15% restocking fee. BMR also states that racing parts and equipment are used under varied conditions, that the suitability of any part for a particular application is solely the purchaser's decision, and that BMR makes no warranties, express, implied or written, and that there is no warranty of merchantability; BMR reserves the right to change designs without obligation to modify previously manufactured units, and the buyer agrees to indemnify and hold BMR harmless from any claim arising from installation or use. Separately from warranty, non-warranty returns must be made within 90 days of shipment and carry a 15% restocking fee (shipping costs excluded): items that have been installed, used, modified or damaged are not accepted, everything must come back in its original packaging with an RMA and freight prepaid (collect shipments are refused), any scratch or damage is deducted at the cost to repair or re-powder coat, missing components are deducted at replacement cost, and special order items cannot be returned.

Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by BMR Suspension. Contact us if you need help with a warranty claim.

View full details

Q&A

0 answered questions

No questions yet. Be the first to ask!